ACV-LFB Nissan/Opel/Renault 40Pin Quadlock steering wheel remote control-Masori.de
ACV-LFB Nissan/Opel/Renault 40Pin Quadlock steering wheel remote control-Masori.de
ACV-LFB Nissan/Opel/Renault 40Pin Quadlock steering wheel remote control-Masori.de

ACV LFB Nissan/Opel/Renault 40Pin Quadlock

Steering wheel remote control

Normal price Special price Normal price 109,99€

/piece

(/ )

VAT included. Excl. VAT incl. shipping costs excl. shipping costs

The quantity exceeds the available stock.

Your advantages with Masori

0% financing on all products

Advice from Carhifi experts

Seen this item cheaper elsewhere? Write us an email at [email protected] and you will get the same price, plus a free accessory and benefit from Masori Lifetime Support! Warranty conditions.

Description

    If you want to replace your factory radio with an aftermarket radio, you should make sure that you retain the original steering wheel remote control functions.

    However, please note that depending on the vehicle equipment, range of functions and software of the aftermarket device, individual operating functions may be omitted or replaced by other functions.

    Compare the adapter plugs shown with those in your vehicle and make sure that they match visually and technically.

    Please also check whether one of the specified original factory radios was installed in your vehicle.

    Before you finally install the retrofit radio, we recommend that you check the functions of your vehicle, the vehicle settings and the steering wheel remote control to ensure that everything is working properly.

Note

CAN bus
    • Anschluss: 40 Pin Quadlock Opel Stecker > Artikel: 42cx21
    • Check dip switch position for retrofit device
    • Fahrzeuge mit CD30 / CD30MP / CDC40 / CD50 / CD70 / DVD 90 OEM Gerät
    • Vehicle settings not supported
    • Fahrzeuge Opel Corsa D (S07) 10/2006 - 08/2014 Fahrzeugeinstellungen unterstützt > Lenkstock Wischerhebel
Fahrzeuge Opel Corsa D (S07) 10/2006 - 08/2014 mit Interfaceausfall nach längerer Betriebszeit
    • 1: OEM Gerät anschließen
    • 2: CAN Bus Ruhe herstellen
    • 3: CAN Bus Alternativabgriff > 32 Pin OEM Displaystecker Can High / Can Low > Pin 20 / Pin 23
    • 4: CAN Bus Alternativabgriff > Komfort-CAN an Klimatronik

Suitable for the following vehicles

Opel
    • Opel Antara (L-A) 11/2006 - 11/2010
    • Opel Antara (L-A) 01/2011 - 03/2015
    • Opel Agila A (H00) 06/2003 - 10/2007
    • Opel Astra H (A-H) 03/2004 - 02/2007
    • Opel Astra H (A-H) 02/2007 - 11/2010
    • Opel Combo (C) 10/2004 - 09/2011
    • Opel Corsa C (X01) 07/2003 - 07/2006
    • Opel Corsa D (S07) 10/2006 - 11/2010
    • Opel Corsa D (S07) 01/2011 - 08/2014
    • Opel Meriva A (X01) 11/2005 - 03/2010
    • Opel Signum I (Z03) 09/2005 - 08/2008
    • Opel Tigra Twin Top (X-C) 07/2004 - 11/2009
    • Opel Vectra C (Z02) 09/2005 - 09/2008
    • Opel Vivaro A (X83) 09/2006 - 01/2011
    • Opel Zafira B (A-H) 07/2005 - 06/2010
    • Opel Zafira B (A-H) 02/2008 - 12/2014
Nissan
    • Nissan Primastar (X83) 09/2006 - 01/2011*
Renault
    • Renault Trafic II (L/jL) 10/2006 - 01/2011*

The following signals are provided

    • Reimported vehicles or vehicles with different software may be incompatible in terms of functions.
    • pink: +12V ignition terminal 15 1.5A max.
    • orange: +12V lighting terminal 58 0.1A max.
    • white: +12V reversing signal 1.5A max.
    • yellow/green yellow/red: speed signal
    • grau: keine Funktion
    • Steering wheel remote control
    • *Fahrzeuge mit mit trapezförmigem OEM Gerät

Connection cable for the following radio manufacturers

    • Multilead various devices: 42arc100
    • Alpine 3.5mm jack connection: 42arc101
    • Blaupunkt 2010> 3.5mm jack connection: 42arc107
    • Blaupunkt 2010> Key1 / Key2 / (GND) connection: 42arc000
    • China HU Key1 / Key2 / (GND) Connection: 42arc000
    • Clarion 3.5mm jack connection: 42arc104
    • Digital Dynamics single cable connection: 42arc108
    • ESX Key1 / Key2 connection: 42arc000
    • JVC 3.5mm jack connection: 42arc104
    • JVC single cable connection: 42arc105
    • Kenwood single cable connection: 42arc105
    • Kenwood 2017> 3.5mm jack connection: 42arc107
    • Kenwood 2020> Key1 / Key2 / GND Connection: 42arc000
    • Pioneer 3.5mm jack connection: 42arc107
    • Pioneer AVH/DMH/SPH 3,5mm Klinkenanschluss: 42arc1072
    • Snooper Key1 / Key2 connection: 42arc000
    • Sony 3.5mm jack connection: 42arc107
    • XZent single cable connection: 42arc108
    • Zenec single cable connection: 42arc108

General installation instructions

Connection and connection sequence
    • 1: Carry out settings and configuration of the interface without voltage
    • 2: Check the configuration of the radio connection cable
    • 3: Connect the radio connection cable according to the operating instructions for the retrofit device
    • 4: Connect all other connections according to the operating instructions for the retrofit device
    • 5: Connection of the complete installation to the vehicle with live connection last
    • 6: Configuration of the retrofit device according to the operating instructions for the retrofit device Steering wheel remote control/camera/FSE/antenna phantom power and others
Changes to the configuration of the interface and the radio connection cable
    • 1: Carry out changes without tension
    • 2: Connection after modification see above 5 and 6
  • Connections, connection changes, alternative connections, connections of loose cables or connection extensions of loose cables specified in the information text or the operating instructions are for guidance and information purposes only for trained specialist personnel.
Connections, changes to the cable configuration of the wiring harness or use of alternative connections or connection extensions
    • 1: Connections and modifications must only be carried out by trained specialist personnel
    • 2: Connections and modifications must be checked for any manufacturer approvals or manufacturer warranty conditions that may be affected by the modifications before connection
    • 3: Connections and modifications must be checked for function and correctness before connection by measuring and adjusting using the vehicle's cable assignment diagram
    • 4: Connections and modifications are made on your own responsibility without any guarantee of function
    • 5: Connections and modifications are carried out under your own responsibility without guarantee of damage to the vehicle, the retrofit device or the interface
    • 6: Änderungen am vorkonfektionierten Kabelbaum können zum Erlöschen der Garantie des Produktes führen