If you want to replace your factory radio with an aftermarket radio, you should ensure that the original steering wheel remote control functions are retained.

However, please note that depending on the vehicle equipment, functionality, and software of the retrofit device, certain operating functions may be omitted or replaced by other functions.

Compare the illustrated plugs of the adapter with those in your vehicle and ensure that they fit visually and technically.

Please also check if one of the specified original factory radios was installed in your vehicle.

Before you permanently install the retrofit radio, we recommend that you check the functions of your vehicle, the vehicle settings, and the steering wheel remote control for their functionality to ensure that everything works smoothly.

Note

• CAN Bus
• Connection: 40 Pin Quadlock MAN Connector +12V
• Connection: +12V Power Supply
• Vehicles with +24 Volt power supply
• Voltage converter 24 Volt > 12 Volt max. 10A > Article: 30.3520-06
• Vehicles with OEM subwoofer MQS connector pinout 40 Pin Quadlock:
• Check occupancy with OEM device before installation
• B11: +12V Amp Remote
• D10: Preamp-GND 2V max.
• D11: Preamp-R 2V max.
• D12: Pramp-L 2V max.
• Vehicles with OEM camera MQS connector pin assignment 40 pin Quadlock
• Check occupancy with OEM device
• D3: Video+
• D4: Video-
• +24V reverse signal
• Check dip switch setting of steering wheel remote control on retrofit device (see user manual)
• Check dip switch setting vehicle equipment (see BDA)

Suitable for the following vehicles

• MAN TGA 2007 -2020*
• MAN TGL 2007 - 2020*
• MAN TGM 2007 - 2020*
• MAN TGS 2007 - 2020*
• MAN TGX 2007 - 2020*

The following signals are provided.

• Reimport vehicles or vehicles with differing software may be incompatible in functions.
• +12V ignition terminal 15
• +12V lighting terminal 58
• +12V reverse signal
• speed signal
• Load capacity total outputs: 200 mA max.
• Load capacity single output: 180 mA max.
• Current demand greater than 180 mA
• 1 Relay coil resistance 75 Ohm min.
• 2 Relay Coil Resistance 150 Ohm min.
• steering wheel remote control
• *Vehicles with 42 Pin Quadlock Connector Retrofit Adapter VAG 42Pin Quadlock>40Pin Quadlock > Article: 321328-24
• *CAN Bus high/low black/blue//brown/black > MQS connector B6/B12
• *Vehicles with ISO connection > CAN bus in ISO power connector

Optional

• 2-DIN Radio Frame MAN TGA/TGL/TGM/TGS/TGX Rubber Touch > Article: 391165-01

Connection cable for the following radio manufacturers

• LFB Speed Signal Cable > Blaupunkt 2010>/Pioneer/Sony 4 Pin: 42c-3474101
• LFB Speedsignal Cable > JVC/Kenwood/XZent/Zenec 1 Lead 4 Pin: 42c-3474104
• LFB Speedsignal Cable > Alpine/Clarion/JVC 3.5mm jack 4 Pin: 42c-3474105
• LFB Speedsignal Cable > Blaupunkt 2010>/China HU Lead 4 Pin: 42c-3474124

General Installation Instructions

• Review
• 1: Review of all operating functions and vehicle adjustment functions of the OEM device
• 2: Carry out the disassembly of the OEM device without voltage.
• 3: Check all interface connections for correctness and continuity without voltage.
• Connection and connection sequence
• 1: Make settings and hardware configuration of the interface without voltage.
• 2: Check configuration of the radio connection cable
• 3: Connect the radio connection cable according to the operating instructions of the retrofit device.
• 4: Connect all other connections according to the operating instructions of the retrofit device.
• 5: Connection of the complete installation to the vehicle with live connection last
• 6: Software configuration of the interface according to the instructions in the article text and in the BDA
• 7: Configuration of the retrofit device according to the operating instructions of the retrofit device steering wheel remote control/camera/telephone hands-free system/antenna phantom power supply and more
• 8: Function test steering wheel remote control and vehicle
• Changes to the hardware configuration of the interface and the radio connection cable
• 1: Carry out changes without tension
• 2: Connection after change see above 5 to 8
• In case of malfunction of the interface or the vehicle
• 1: Reversion to the OEM device
• 2: Operate OEM device
• 3: Establish CAN Bus idle
• 4: Review of the hardware configuration of the interface
• 5: Connection to CAN Bus idle see above 5 to 8
• The connections, connection changes, alternative connections, connections of loose cables, or connection extensions of loose cables specified in the instructions or the operating manual are intended solely for orientation and information for trained professionals.
• Further connections, changes to the cable configuration of the wiring harness, or use of alternative connections or connection extensions.
• 1: Connections and modifications are to be carried out exclusively by trained professionals.
• 2: Connections and modifications must be checked for any manufacturer approvals or any manufacturer warranty conditions that may be affected by the modifications before connection.
• 3: Connections and modifications must be checked for functionality and accuracy before connection by measuring and by matching against the vehicle's wiring diagram.
• 4: Connections and changes are made at your own risk without any guarantee of functionality.
• 5: Connections and modifications are made at your own risk without any guarantee against damage to the vehicle, the retrofit device, or the interface.
• 6: Modifications to the pre-assembled wiring harness may lead to the expiration of the product's warranty.