Keep your original steering wheel remote control functions when replacing your factory radio with an aftermarket radio.

Depending on the vehicle equipment, functionality, and software of the retrofit device, certain operating functions may be omitted or replaced by other functions.

Compare the illustrated plugs of the adapter with those in your vehicle and ensure that they fit visually and technically.

Please also check if one of the specified original factory radios was installed in your vehicle.

Before the final assembly, please check the functions of your vehicle, the vehicle settings, and the steering wheel remote control for their functionality.

Note

• CAN Bus
• Connection: 52 Pin Fiat Connector
• Vehicles Alfa Romeo with touchscreen OEM device
• Vehicles Citroen/Fiat/Opel/Peugeot with Continental VP1 / VP2 OEM device
• Vehicles Citroen/Fiat/Opel/Peugeot with Daiichi OEM device*
• Vehicle settings not supported**
• Date/Time settings supported (see user manual)
• Check dip switch setting of steering wheel remote control on retrofit device (see user manual)
• Check dip switch setting vehicle equipment (see BDA)

Suitable for the following vehicles

• Alfa Romeo
• Alfa Romeo Giulietta (940) 10/2013 - 04/2016
• Alfa Romeo Giulietta (940) 04/2016 - 12/2021
• Alfa Romeo Mito (955) 05/2010 - 08/2016
• Alfa Romeo Mito (955) 08/2016 - 08/2018
• Citroen
• Citroen Jumper (250) 05/2014 - 2023
• Citroen Relay (250) 05/2014 - 2023
• Fiat
• Fiat Ducato (ZFA 250) 05/2014 - 11/2021
• Opel
• Opel Movano Cargo C (Y) 10/2021 - 2023
• Peugeot
• Peugeot Boxer (Y) 05/2014 - 2023

The following signals are provided.

• Reimport vehicles or vehicles with differing software may be incompatible in functions.
• +12V ignition terminal 15
• +12V Lighting Terminal 58
• +12V reverse signal
• speed signal
• Load capacity total outputs: 200 mA max.
• Load capacity single output: 180 mA max.
• Current demand greater than 180 mA:
• 1 Relay Coil Resistance 75 Ohm min.
• 2 Relay coil resistance 150 Ohm min.
• steering wheel remote control
• Date/Time settings supported
• *Vehicles with Daiichi OEM device wiring harness black cable > Adapter wiring harness radio compartment driver side disassemble
• *Vehicles with directly wired OEM Daiichi device colored cables not compatible > contact support
• **Citroen/Fiat/Opel/Peugeot On-Board Computer Vehicle Settings Info Adapter:
• Infodapter Citroen/Fiat/Opel/Peugeot 52Pin Fiat VP1/VP2 > Article: 43uft01

Connection cable for the following radio manufacturers

• LFB Speed Signal Cable > Blaupunkt 2010>/Pioneer/Sony 4 Pin: 42c-3474101
• LFB Speedsignal Cable > JVC/Kenwood/XZent/Zenec 1 Lead 4 Pin: 42c-3474104
• LFB Speedsignal Cable > Alpine/Clarion/JVC 3.5mm jack 4 Pin: 42c-3474105
• LFB Speedsignal Cable > Blaupunkt 2010>/China HU Lead 4 Pin: 42c-3474124

General Installation Instructions

• Review
• 1: Review of all operating functions and vehicle adjustment functions of the OEM device
• 2: Carry out disassembly of the OEM device without voltage
• 3: Check all interface connections for correctness and continuity without voltage.
• Connection and connection sequence
• 1: Make settings and hardware configuration of the interface without voltage
• 2: Check the configuration of the radio connection cable
• 3: Connect the radio connection cable according to the operating instructions of the retrofit device.
• 4: Connect all other connections according to the operating instructions of the retrofit device.
• 5: Connection of the complete installation to the vehicle with live connection last
• 6: Software configuration of the interface according to the instructions in the article text and in the BDA
• 7: Configuration of the retrofit device according to the operating instructions of the retrofit device steering wheel remote control/camera/telephone hands-free system/antenna phantom power supply and more
• 8: Function test steering wheel remote control and vehicle
• Changes to the hardware configuration of the interface and the radio connection cable
• 1: Carry out changes without tension
• 2: Connection after change see above 5 to 8
• In case of malfunction of the interface or the vehicle
• 1: Reversion to the OEM device
• 2: Operate OEM device
• 3: Establish CAN Bus idle
• 4: Review of the hardware configuration of the interface
• 5: Connection to CAN Bus idle see above 5 to 8
• The connections, connection changes, alternative connections, connections of loose cables, or connection extensions of loose cables specified in the instructions or the operating manual are intended solely for orientation and information for trained professional personnel.
• Further connections, changes to the cable configuration of the wiring harness, or use of alternative connections or connection extensions.
• 1: Connections and modifications are to be carried out exclusively by trained professionals.
• 2: Connections and modifications must be checked for any manufacturer approvals or any manufacturer warranty conditions that may be affected by the modifications before connection.
• 3: Connections and modifications must be checked for functionality and accuracy before connection by measuring and by matching against the vehicle's wiring diagram.
• 4: Connections and modifications are made at your own risk without guarantee of functionality.
• 5: Connections and modifications are made at your own risk without any guarantee against damage to the vehicle, the retrofitting device, or the interface.
• 6: Modifications to the pre-assembled wiring harness may result in the expiration of the product's warranty.