ACV LFB Mercedes ISO/10 Pin ISO/Mini ISO
Steering wheel remote control
/Stück
Günstiger gesehen?
„Wir halten mit - garantiert!" Nutze die Tiefpreisgarantie! Wenn du einen Artikel auf einer Internetseite innerhalb der EU günstiger findest, ziehen wir mit dem Preis der Konkurrenz gleich und legen einen Artikel aus unserem Zubehörsortiment bei.
Beschreibung
If you want to replace your factory radio with an aftermarket radio, you should make sure to retain the original steering wheel remote control functions.
Please note, however, that depending on the vehicle equipment, range of functions and software of the retrofit device, individual operating functions may be omitted or replaced by other functions.
Compare the adapter plugs shown with those in your vehicle and make sure they fit visually and technically.
Please also check whether one of the specified original factory radios was installed in your vehicle.
Before you finally install the retrofit radio, we recommend that you check your vehicle's functions, vehicle settings and steering wheel remote controls to ensure that everything is working smoothly.
Notice
CAN bus
- Connection: ISO / 10 Pin ISO / Mini ISO connector Mercedes
- Check dip switch position for retrofit device
- Mercedes vehicles with Audio 5 / Audio 10 1-DIN OEM device
- Mercedes vehicles with Audio 30 APS 1-DIN OEM Navigation
- Vehicles VW Crafter with RCD 2001 1-DIN OEM device
- Mercedes / VW vehicles with radio preparation > Check connection and assignment before installation with OEM device:*
Vehicles with different comfort interior CAN bus connection
- brown-red twisted: CAN high
- brown twisted: CAN low
- CAN Bus to CAN Bus distributor sill strip
- CAN bus to climate control
- CAN bus in Mini ISO connector: Pin 1 Can low / Pin 2 Can high
- CAN bus in 8 pin ISO power connector: Pin 7 CAN high / Pin 6 CAN low
- CAN bus in 18 pin AMP connector: Pin 8 CAN low / Pin 9 CAN high / not Robert-Bosch CAN
OEM devices with ISO block connection
- ISO extension speaker 10cm > Article: 1322-02
- Vehicles with 10 pin ISO / ISO speaker connector OEM sound system without D2B OEM sound system:
- Active system adapter various vehicles ISO>ISO > Article: 13-1190-50
Suitable for the following vehicles
- Mercedes A-Class (W169 ) 10/2004 - 04/2012
- Mercedes A-Class (C169) 11/2004 - 07/2011
- Mercedes B-Class (T245) 06/2005 - 06/2011
- Mercedes C-Class (W203 ) 03/2000 - 01/2005
- Mercedes CLK-Class (C208) 07/1999 - 03/2003
- Mercedes CLK-Class (C209) 03/2002 - 05/2005
- Mercedes E-Class (W210 ) 06/1999 - 12/2002
- Mercedes SL-Class (R230) 08/2001 - 02/2006
- Mercedes SLR (C199) 13/2003 - 12/2009
- Mercedes Sprinter (W906 ) 04/2006 - 08/2013
- Mercedes Sprinter (W906 ) 08/2013 - 05/2018
- Mercedes Vito/Viano (W639 ) 07/2003 - 08/2010
- Mercedes Vito/Viano (W639 ) 07/2003 - 08/2010
- Mercedes Vito/Viano (W639 ) 09/2010 - 03/2014
VW
- VW Crafter I (2EC/2EK/2F) 03/2006 - 07/2011
- VW Crafter I (2EC/2EK/2F) 07/2011 - 11/2016
VW
- VW Crafter I (2EC/2EK/2F) 03/2006 - 07/2011
- VW Crafter I (2EC/2EK/2F) 07/2011 - 11/2016
The following signals are provided
- Reimported vehicles or vehicles with different software may be functionally incompatible.
- pink: +12V ignition terminal 15 1.5A max.
- orange: +12V lighting terminal 58 0.1A max.
- white: +12V reverse signal 1.5A max.
- yellow/green yellow/red: speed signal
- steering wheel remote control
Connection cables for the following radio manufacturers
- Reimported vehicles or vehicles with different software may be functionally incompatible.
- pink: +12V ignition terminal 15 1.5A max.
- orange: +12V lighting terminal 58 0.1A max.
- white: +12V reversing signal 1.5A max.
- yellow/green yellow/red: speed signal
- steering wheel remote control
Connection cables for the following radio manufacturers
- Multilead various devices: 42arc100
- Alpine 3.5mm jack connector: 42arc101
- Blaupunkt 2010> 3.5mm jack connection: 42arc107
- Blaupunkt 2010> Key1 / Key2 / (GND) Connection: 42arc000
- China HU Key1 / Key2 / (GND) Connector: 42arc000
- Clarion 3.5mm jack connector: 42arc104
- Digital Dynamics single cable connection: 42arc108
- ESX Key1 / Key2 Connector: 42arc000
- JVC 3.5mm jack connector: 42arc104
- JVC single cable connection: 42arc105
- Kenwood single cable connection: 42arc105
- Kenwood 2017> 3.5mm jack connection: 42arc107
- Kenwood 2020> Key1 / Key2 / GND connection: 42arc000
- Pioneer 3.5mm jack connector: 42arc107
- Snooper Key1 / Key2 connection: 42arc000
- Sony 3.5mm jack: 42arc107
- XZent single cable connection: 42arc108
- Zenec single cable connection: 42arc108
General Installation Instructions
connection and connection sequence
- 1: Make settings and configuration of the interface without power
- 2: Check the configuration of the radio connection cable
- 3: Connect the radio connection cable according to the operating instructions of the retrofit device
- 4: Connect all other connections according to the operating instructions of the retrofit device
- 5: Connection of the entire installation to the vehicle with the live connection last
- 6: Configuration of the retrofit device according to the operating instructions of the retrofit device steering wheel remote control/camera/FSE/antenna phantom power and others
Changes to the configuration of the interface and the radio connection cable
- 1: Make changes without stress
- 2: Connection after modification see above 5 and 6
- Connections, connection changes, alternative connections, connections of loose cables or connection extensions of loose cables specified in the information text or the operating instructions are intended solely for orientation and information purposes for trained specialist personnel.
connections, changes to the cable configuration of the wiring harness or use of alternative connections or connection extensions
- 1: Connections and modifications must only be carried out by trained personnel
- 2: Connections and modifications must be checked before connection for any manufacturer approvals or manufacturer warranty conditions that may be affected by the modifications
- 3: Connections and changes must be checked for functionality and correctness before connection by measuring and comparing them with the vehicle's cable assignment plan
- 4: Connections and modifications are carried out at your own risk without guarantee of functionality
- 5: Connections and modifications are carried out at your own risk without any guarantee for damage to the vehicle, the retrofit device or the interface
- 6: Modifications to the pre-assembled wiring harness will void the product warranty
Datenblatt herunterladen
