ACV LFB Honda 17 pin/20 pin analogue

Beschreibung

If you want to replace your factory radio with an aftermarket radio, you should make sure to retain the original steering wheel remote control functions.

Please note, however, that depending on the vehicle equipment, range of functions and software of the retrofit device, individual operating functions may be omitted or replaced by other functions.

Compare the adapter plugs shown with those in your vehicle and make sure they fit visually and technically.

Please also check whether one of the specified original factory radios was installed in your vehicle.

Before you finally install the retrofit radio, we recommend that you check your vehicle's functions, vehicle settings and steering wheel remote controls to ensure that everything is working smoothly.

Notice

Analog

• Connection: 17 pin / 20 pin Honda connector
• Vehicles with Panasonic / Pioneer  OEM device

Suitable for the following vehicles

• Honda Civic (FN/FD/FG/FA/FK) 09/2005 - 12/2011*
• Honda Civic Hybrid (FD3) 04/2006 - 10/2010*
• Honda CR-V (RE5) 01/2007 - 02/2010**
• Honda CR-V (RE5) 04/2010 -  10/2012**
• Honda S2000 (AP1) 01/2004 - 06/2009

The following signals are provided

• steering wheel remote control
• *Vehicles without OEM navigation
• *Vehicles with climate control / display > Article: 42sho002
• **Vehicles with ZVN0 OEM Navigation LFB connection 22 pin connector green  > Pin 4 / Pin 5 (see BDA)

Connection cables for the following radio manufacturers

• LFB InCartec cable > Blaupunkt/China HU/Kenwood: 42k-000
• LFB InCartec cable > Multilead various devices: 42k-025
• LFB InCartec cable > Alpine: 42k-100
• LFB InCartec cable > Blaupunkt/Kenwood/Pioneer: 42k-300
• LFB InCartec cable > XZent/Zenec: 42k-400
• LFB InCartec Cable > Sony: 42k-600
• LFB InCartec cable > Kenwood: 42k-700a
• LFB InCartec Cable > Clarion: 42k-800
• LFB InCartec cable > JVC: 42k-900

General Installation Instructions

examination

• 1: Checking all operating functions and vehicle setting functions of the OEM device
• 2: Disassemble the OEM device without applying any voltage
• 3: Check all interface connections for correctness and continuity without voltage

connection and connection sequence

• 1: Make settings and hardware configuration of the interface without power
• 2: Check the configuration of the radio connection cable
• 3: Connect the radio connection cable according to the operating instructions of the retrofit device
• 4: Connect all other connections according to the operating instructions of the retrofit device
• 5: Connection of the entire installation to the vehicle with the live connection last
• 6: Software configuration of the interface according to the instructions in the article text and in the BDA
• 7: Configuration of the retrofit device according to the operating instructions of the retrofit device steering wheel remote control/camera/FSE/antenna phantom power and others
• 8: Functional test of steering wheel remote control and vehicle

Changes to the hardware configuration of the interface and the radio connection cable

• 1: Make changes without stress
• 2: Connection after change see above 5 to 8

In case of malfunction of the interface or the vehicle

• 1: Revert to the OEM device
• 2: Operating the OEM device
• 3: Establish CAN bus rest
• 4: Checking the hardware configuration of the interface
• 5: Connection after CAN bus rest see above 5 to 8
• Connections, connection changes, alternative connections, connections of loose cables or connection extensions of loose cables specified in the information text or the operating instructions are intended solely for orientation and information purposes for trained specialist personnel.

Additional connections, changes to the cable configuration of the wiring harness or use of alternative connections or connection extensions

• 1: Connections and modifications must only be carried out by trained personnel
• 2: Connections and modifications must be checked before connection for any manufacturer approvals or manufacturer warranty conditions that may be affected by the modifications
• 3: Connections and changes must be checked for functionality and correctness before connection by measuring and comparing them with the vehicle's cable assignment plan
• 4: Connections and modifications are carried out at your own risk without guarantee of functionality
• 5: Connections and modifications are carried out at your own risk without any guarantee for damage to the vehicle, the retrofit device or the interface
• 6: Modifications to the pre-assembled wiring harness may void the product warranty01717333659