ACV LFB Citroen/Fiat/Opel/Peugeot VP1/VP2/Daiichi 52Pin

Beschreibung

If you want to replace your factory radio with an aftermarket radio, you should keep the original steering wheel remote control functions.

However, depending on the vehicle equipment, range of functions and software of the retrofit device, it is possible that individual operating functions may be omitted or replaced by other functions.

Compare the adapter plugs shown with those in your vehicle and make sure they fit visually and technically.

Please also check whether one of the specified original factory radios was installed in your vehicle.

Before you finally install the retrofit radio, we recommend that you check the functions of your vehicle, the vehicle settings and the steering wheel remote control to ensure they are working properly.

Notice

CAN bus

• Connection: 52 pin Fiat connector
• Vehicles with Continental 250VP1 / 250VP2 OEM device
• Vehicles with UConnect OEM device
• Vehicles with Daiichi OEM device*

Vehicles with error display of trip odometer after installation > dip switch position under the circuit board

• Adjust dip switch position without voltage
• Dip switch 1 on / Dip switch 2 off / Dip switch 3 on or off
• Dip switch 1 off / Dip switch 2 on / Dip switch 3 on or off
• Dip switch 1 on > 250VP1 OEM HU
• Dip switch 2 on > 250VP2 OEM HU
• Dip switch 3 on > Blue&Me OEM function
• Dip switch 4 on > Pioneer
• Dip switch 1 off / Dip switch 2 off / Dip switch 3 on > Daiichi OEM device
• Restoring CAN bus stability after conversion
• Vehicles with persistent error display and other software package not compatible
• On-board computer vehicle settings not supported**
• High beam assistant not supported
• driver assistance systems not supported
• Date/time setting not supported**

Vehicles with OEM rear view camera assignment OEM connector

• red: Pin 31 Video+
• white: Pin 32 Video -
• black: Pin 33 shielding

Suitable for the following vehicles

Citroen

• Citroen Jumper (250) 05/2014 - 2023*
• Citroen Relay (250) 05/2014 - 2023*

Fiat

• Fiat 500 (ZAF 312) 07/2016 - 2023*
• Fiat 500L (ZAF 199) 10/2012 - 07/2017
• Fiat 500L (ZAF 199) 07/2017 - 03/2022
• Fiat Doblo (ZAF 263) 01/2015 - 06/2022
• Fiat Ducato (ZFA 250) 05/2014 - 11/2021*

Opel

• Opel Movano Cargo C (Y) 10/2021 - 2023*

Peugeot

• Peugeot Boxer (Y) 05/2014 - 2023*

The following signals are provided

• Reimported vehicles or vehicles with different software may be functionally incompatible.
• red: +12V ignition terminal 15
• orange: +12V lighting terminal 58
• purple/white: +12V reversing signal
• pink: speed signal
• green: ground GND handbrake signal
• Total output load capacity: 100 mA max.

current consumption greater than 100 mA

• 1 relay coil resistance 75 Ohm min.
• 2 relays coil resistance 150 Ohm min.
• steering wheel remote control
• *Vehicles with Daiichi OEM device wiring harness black cable > adapter wiring harness radio slot driver side dismantle
• *Vehicles with directly wired OEM Daiichi device colored cables not compatible > contact support/see article: 42sfa016
• **On-board computer vehicle settings info adapter:
• Info adapter Citroen/Fiat/Opel/Peugeot 52Pin Fiat VP1/VP2 > Article: 43uft01

Connection cables for the following radio manufacturers

• LFB cable 42s/acv > Alpine jack: 42ctalpinelead
• LFB cable 42s/acv > Parrot 4 Pin: 42ctasteroidlead
• LFB cable 42s/acv > Bosch-Blaupunkt >2010 Mini ISO: 42ctblaupunktlead
• LFB cable 42s/acv > Blaupunkt/China HU/Kenwood 3 cable: 42ctchinahulead
• LFB cable 42s/acv > Clarion jack: 42ctclarionlead
• LFB cable 42s/acv > JVC 1 cable/jack: 42ctjvclead
• LFB cable 42s/acv > Kenwood 1 cable: 42ctkenwoodlead
• LFB cable 42s/acv > Multilead various devices: 42ctmultilead
• LFB cable 42s/acv > Multilead various devices/Pioneer 2022>: 42ctmultilead3
• LFB cable 42s/acv > Multilead various devices/Pioneer 2022>: 42ctmultilead5
• LFB cable 42s/acv > Panasonic 1 cable: 42ctpanasoniclead
• LFB cable 42s/acv > Blaupunkt/Kenwood/Pioneer jack: 42ctpioneerlead
• LFB cable 42s/acv > Pioneer AVH/DMH/SPH 2022> Jack loose: 42ctpioneerlead2
• LFB cable 42s/acv > Devices with LFB learning function: 42ctsmartlead
• LFB cable 42s/acv > Blaupunkt/Kenwood/Sony jack: 42ctsonylead
• LFB cable 42s/acv > XZent/Zenec 1 cable: 42ctzeneclead

General Installation Instructions

examination

• 1: Checking all operating functions and vehicle setting functions of the OEM device
• 2: Disassemble the OEM device without applying any voltage
• 3: Check all interface connections for correctness and continuity without voltage

connection and connection sequence

• 1: Make settings and hardware configuration of the interface without power
• 2: Check the configuration of the radio connection cable
• 3: Connect the radio connection cable according to the operating instructions of the retrofit device
• 4: Connect all other connections according to the operating instructions of the retrofit device
• 5: Connection of the entire installation to the vehicle with the live connection last
• 6: Software configuration of the interface according to the instructions in the article text and in the BDA
• 7: Configuration of the retrofit device according to the operating instructions of the retrofit device steering wheel remote control/camera/FSE/antenna phantom power and others
• 8: Functional test of steering wheel remote control and vehicle

Changes to the hardware configuration of the interface and the radio connection cable

• 1: Make changes without stress
• 2: Connection after change see above 5 to 8

In case of malfunction of the interface or the vehicle

• 1: Revert to the OEM device
• 2: Operating the OEM device
• 3: Establish CAN bus rest
• 4: Checking the hardware configuration of the interface
• 5: Connection after CAN bus rest see above 5 to 8
• Connections, connection changes, alternative connections, connections of loose cables or connection extensions of loose cables specified in the information text or the operating instructions are intended solely for orientation and information purposes for trained specialist personnel.

Additional connections, changes to the cable configuration of the wiring harness or use of alternative connections or connection extensions

• 1: Connections and modifications must only be carried out by trained personnel
• 2: Connections and modifications must be checked before connection for any manufacturer approvals or manufacturer warranty conditions that may be affected by the modifications
• 3: Connections and changes must be checked for functionality and correctness before connection by measuring and comparing them with the vehicle's cable assignment plan
• 4: Connections and modifications are carried out at your own risk without guarantee of functionality
• 5: Connections and modifications are carried out at your own risk without any guarantee for damage to the vehicle, the retrofit device or the interface
• 6: Modifications to the pre-assembled wiring harness may void the product warranty