ACV LFB Alfa Romeo/Citroen/Fiat/Opel/Peugeot 52Pin

Beschreibung

Keep your original steering wheel remote control functions when replacing your factory radio with an aftermarket radio.

However, depending on the vehicle equipment, range of functions and software of the retrofit device, individual operating functions may be omitted or replaced by other functions.

Compare the adapter plugs shown with those in your vehicle and make sure that they fit visually and technically.

Please also check whether one of the specified original factory radios was installed in your vehicle.

Before final assembly, please check the functions of your vehicle, the vehicle settings and the steering wheel remote control for functionality.

Notice

CAN bus

• Connection: 52 pin Fiat connector
• Vehicles Alfa Romeo with touchscreen OEM device
• Vehicles Citroen/Fiat/Opel/Peugeot with Continental VP1 / VP2 OEM device
• Vehicles Citroen/Fiat/Opel/Peugeot with Daiichi OEM device*
• Vehicle settings not supported**
• Date/Time settings supported (see BDA)
• Check dip switch position of steering wheel remote control on retrofit device (see BDA)
• Dip switch position Check vehicle equipment (see BDA)

Suitable for the following vehicles

Alfa Romeo

• Alfa Romeo Giulietta (940) 10/2013 - 04/2016
• Alfa Romeo Giulietta (940) 04/2016 - 12/2021
• Alfa Romeo Mito (955) 05/2010 - 08/2016
• Alfa Romeo Mito (955) 08/2016 - 08/2018

Citroen

• Citroen Jumper (250) 05/2014 - 2023
• Citroen Relay (250) 05/2014 - 2023

Fiat

• Fiat Ducato (ZFA 250) 05/2014 - 11/2021

Opel

• Opel Movano Cargo C (Y) 10/2021 - 2023

Peugeot

• Peugeot Boxer (Y) 05/2014 - 2023

The following signals are provided

• Reimported vehicles or vehicles with different software may be functionally incompatible.
• +12V ignition terminal 15
• +12V lighting terminal 58
• +12V reversing signal
• speed signal
• Total output load capacity: 200 mA max.
• Load capacity of single output: 180 mA. max
• Current consumption greater than 180 mA:
• 1 relay coil resistance 75 Ohm min.
• 2 relays coil resistance 150 Ohm min.
• steering wheel remote control
• Date/Time settings supported
• *Vehicles with Daiichi OEM device wiring harness black cable > adapter wiring harness radio slot driver side dismantle
• *Vehicles with directly wired OEM Daiichi device colored cables not compatible > contact support
• **Citroen/Fiat/Opel/Peugeot on-board computer vehicle settings info adapter:
• Info adapter Citroen/Fiat/Opel/Peugeot 52Pin Fiat VP1/VP2 > Article: 43uft01

Connection cables for the following radio manufacturers

• LFB Speedsignal cable > Blaupunkt 2010>/Pioneer/Sony 4 Pin: 42c-3474101
• LFB Speedsignal Cable > JVC/Kenwood/XZent/Zenec 1 Lead 4 Pin: 42c-3474104
• LFB Speedsignal Cable > Alpine/Clarion/JVC 3.5mm jack 4 Pin: 42c-3474105
• LFB Speedsignal cable > Blaupunkt 2010>/China HU Lead 4 Pin: 42c-3474124

General Installation Instructions

examination

• 1: Checking all operating functions and vehicle setting functions of the OEM device
• 2: Disassemble the OEM device without applying any voltage
• 3: Check all interface connections for correctness and continuity without voltage

connection and connection sequence

• 1: Make settings and hardware configuration of the interface without power
• 2: Check the configuration of the radio connection cable
• 3: Connect the radio connection cable according to the operating instructions of the retrofit device
• 4: Connect all other connections according to the operating instructions of the retrofit device
• 5: Connection of the entire installation to the vehicle with the live connection last
• 6: Software configuration of the interface according to the instructions in the article text and in the BDA
• 7: Configuration of the retrofit device according to the operating instructions of the retrofit device steering wheel remote control/camera/FSE/antenna phantom power and others
• 8: Functional test of steering wheel remote control and vehicle

Changes to the hardware configuration of the interface and the radio connection cable

• 1: Make changes without stress
• 2: Connection after change see above 5 to 8

In case of malfunction of the interface or the vehicle

• 1: Revert to the OEM device
• 2: Operating the OEM device
• 3: Establish CAN bus rest
• 4: Checking the hardware configuration of the interface
• 5: Connection after CAN bus rest see above 5 to 8
• Connections, connection changes, alternative connections, connections of loose cables or connection extensions of loose cables specified in the information text or the operating instructions are intended solely for orientation and information purposes for trained specialist personnel.

Additional connections, changes to the cable configuration of the wiring harness or use of alternative connections or connection extensions

• 1: Connections and modifications must only be carried out by trained personnel
• 2: Connections and modifications must be checked before connection for any manufacturer approvals or manufacturer warranty conditions that may be affected by the modifications
• 3: Connections and changes must be checked for functionality and correctness before connection by measuring and comparing them with the vehicle's cable assignment plan
• 4: Connections and modifications are carried out at your own risk without guarantee of functionality
• 5: Connections and modifications are carried out at your own risk without any guarantee for damage to the vehicle, the retrofit device or the interface
• 6: Modifications to the pre-assembled wiring harness may void the product warranty