ACV LFB Citroen/Fiat/Opel/Peugeot ISO/Mini ISO analog

Beschreibung

If you want to replace your factory radio with an aftermarket radio, you should make sure to retain the original steering wheel remote control functions.

Please note, however, that depending on the vehicle equipment as well as the range of functions and software of the retrofit device, individual operating functions may be omitted or replaced by other functions.

Compare the adapter plugs shown with those in your vehicle and make sure they fit visually and technically.

Please also check whether one of the specified original factory radios was installed in your vehicle.

Before final assembly, you should check the functions of your vehicle as well as the vehicle settings and the steering wheel remote control to ensure they are working properly.

Notice

Analog

• Connection: ISO / Mini ISO
• Vehicles with radio preparation
• Vehicles with +12V ignition current and analog LFB in the mini-ISO connector pin 10/11/12 SWC1/GND/SWC2
• Vehicles without OEM device
• If the LFB functions are reversed, swap the green/blue cable in the plug contact

Vehicles with Daiichi OEM device directly wired with colored cables

• Check analog signals before installation with OEM device > Article image 2
• Pin 3: Ground GND handbrake signal
• Pin 4: speed signal
• Pin 5: +12V lighting terminal 58
• Pin 8: SWC GND
• Pin 9: Key 1 > green
• Pin 10: Key 2 > blue
• Pin 19: +12V reverse signal
• Pin 28: Ground GND Mute signal
• Pin 42: +12V ignition terminal 15
• If the LFB functions are reversed, swap the green/blue cable in the plug contact
• Adaptation T-cable set Citroen/Dodge/Fiat/Jeep/Opel/Peugeot 52Pin > Article: 57-1095

Suitable for the following vehicles

Citroen

• Citroen Jumper (250) 05/2014 - 2024
• Citroen Relay (250) 05/2014 - 2024

Fiat

• Fiat Ducato (ZFA 250) 05/2014 - 11/2021

Opel

• Opel Movano Cargo C (Y) 10/2021 - 2024

Peugeot

• Peugeot Boxer (Y) 09/2014 - 2024

The following signals are provided

• steering wheel remote control

Connection cables for the following radio manufacturers

• LFB cable 42s/acv > Alpine jack: 42ctalpinelead
• LFB cable 42s/acv > Parrot 4 Pin: 42ctasteroidlead
• LFB cable 42s/acv > Bosch-Blaupunkt  >2010 Mini ISO: 42ctblaupunktlead
• LFB cable 42s/acv > Blaupunkt/China HU/Kenwood 3 cable: 42ctchinahulead
• LFB cable 42s/acv > Clarion jack: 42ctclarionlead
• LFB cable 42s/acv > JVC 1 cable/jack: 42ctjvclead
• LFB cable 42s/acv > Kenwood 1 cable: 42ctkenwoodlead
• LFB cable 42s/acv > Multilead various devices: 42ctmultilead
• LFB cable 42s/acv > Multilead various devices/Pioneer 2022>: 42ctmultilead3
• LFB cable 42s/acv > Multilead various devices/Pioneer 2022>: 42ctmultilead5
• LFB cable 42s/acv > Panasonic 1 cable: 42ctpanasoniclead
• LFB cable 42s/acv > Blaupunkt/Kenwood/Pioneer jack: 42ctpioneerlead
• LFB cable 42s/acv > Pioneer AVH/DMH/SPH 2022> Jack loose: 42ctpioneerlead2
• LFB cable 42s/acv > Devices with LFB learning function: 42ctsmartlead
• LFB cable 42s/acv > Blaupunkt/Kenwood/Sony jack: 42ctsonylead
• LFB cable 42s/acv > XZent/Zenec 1 cable: 42ctzeneclead

General Installation Instructions

examination

• 1: Checking all operating functions and vehicle setting functions of the OEM device
• 2: Disassemble the OEM device without applying any voltage
• 3: Check all interface connections for correctness and continuity without voltage

connection and connection sequence

• 1: Make settings and hardware configuration of the interface without power
• 2: Check the configuration of the radio connection cable
• 3: Connect the radio connection cable according to the operating instructions of the retrofit device
• 4: Connect all other connections according to the operating instructions of the retrofit device
• 5: Connection of the entire installation to the vehicle with the live connection last
• 6: Software configuration of the interface according to the instructions in the article text and in the BDA
• 7: Configuration of the retrofit device according to the operating instructions of the retrofit device steering wheel remote control/camera/FSE/antenna phantom power and others
• 8: Functional test of steering wheel remote control and vehicle

Changes to the hardware configuration of the interface and the radio connection cable

• 1: Make changes without stress
• 2: Connection after change see above 5 to 8

In case of malfunction of the interface or the vehicle

• 1: Revert to the OEM device
• 2: Operating the OEM device
• 3: Establish CAN bus rest
• 4: Checking the hardware configuration of the interface
• 5:  Connection to  CAN bus rest  see above 5 to 8
• Connections, connection changes, alternative connections, connections of loose cables or connection extensions of loose cables specified in the information text or the operating instructions are intended solely for orientation and information purposes for trained specialist personnel.

Additional connections, changes to the cable configuration of the wiring harness or use of alternative connections or connection extensions

• 1: Connections and modifications must only be carried out by trained personnel
• 2: Connections and modifications must be checked before connection for any manufacturer approvals or manufacturer warranty conditions that may be affected by the modifications
• 3: Connections and changes must be checked for functionality and correctness before connection by measuring and comparing them with the vehicle's cable assignment plan
• 4: Connections and modifications are carried out at your own risk without guarantee of functionality
• 5: Connections and modifications are carried out at your own risk without any guarantee for damage to the vehicle, the retrofit device or the interface
• 6: Modifications to the pre-assembled wiring harness may void the product warranty