ACV LFB Mercedes ISO +12V
Steering wheel remote control
/piece
Seen cheaper?
"We keep up - guaranteed!" Take advantage of the low price guarantee! If you find an item cheaper on a website within the EU, we will match the competitor's price and add an item from our range of accessories.
Your advantages with Masori
Description
If you want to replace your factory radio with an aftermarket radio, you should make sure that you retain the original steering wheel remote control functions.
However, please note that depending on the vehicle equipment, range of functions and software of the aftermarket device, individual operating functions may be omitted or replaced by other functions.
Compare the adapter plugs shown with those in your vehicle and make sure that they match visually and technically.
Please also check whether one of the specified original factory radios was installed in your vehicle.
Before you finally install the retrofit radio, we recommend that you check the functions of your vehicle, the vehicle settings and the steering wheel remote control to ensure that everything is working properly.
Note
CAN bus
- Anschluss: ISO Stecker +12V Bordnetzspannung
- Fahrzeuge mit +12V Bordnetzspannung
- Fahrzeuge mit +24 Volt Bordnetzspannung: Spannungswandler 24 Volt > 12
- Volt max. 10A > Artikel: 30.3520-06
- Fahrzeuge mit Radiovorbereitung: Radio muss codiert werden > wenn notwendig
- Fahrzeuge Actros 5 / Arocs 5 mit runden Lenkradfernbedienungstasten
- Fahrzeuge Actros 5 / Arocs 5 mit Multimedia Radio Touch OEM Gerät
- Vehicle settings not supported
Suitable for the following vehicles
- Mercedes Actros 4 (4Gen/MP4) 2011 - 2019*
- Mercedes Actros 5 (5Gen/MP5) 2019 - 2023*
- Mercedes Arocs 1 (1Gen) 2013 - 2019*
- Mercedes Arocs 2 (2Gen) 2019 - 2023*
- Mercedes Atego 2 (2Gen) 2013 - 2023**
- Mercedes Econic 2 (2Gen) 2013 - 2023***
The following signals are provided
- Reimported vehicles or vehicles with different software may be incompatible in terms of functions.
- +12V ignition terminal 15
- +12V Lighting terminal 58
- +12V reverse signal
- Speed signal
- Total output load capacity: 200 mA max.
- Load capacity single output: 180 mA. max
Current requirement greater than 180 mA
- 1 relay Coil resistance 75 Ohm min.
- 2 Ralais Coil resistance 150 Ohm min.
- Steering wheel remote control
- *12V Radiovorbereitung CAN Bus Anschluss Klimatronik 20 Pin Stecker Pin 1 gelb-high/Pin 11 blau-low
- **CAN BUS Anschluss Kombiinstrument 18 Pin Pin 9 blau-weiss/Pin 18 weiss-grün high/low
- **nur Lenkradfernbedienung Funktion laut/leise Telefon annehmen/auflegen
- ***12V Radiovorbereitung CAN Bus Anschluss Kombiinstrument Z1 Sternpunkt X1.18/19 und X1.18/12 gelb-high/blau-low
Connection cable for the following radio manufacturers
- LFB speed signal cable > Blaupunkt/Kenwood/Pioneer 12 pin: 42c-3414101
- LFB speed signal cable > Kenwood 12 pin: 42c-3414104
- LFB speed signal cable > Alpine 12 pin: 42c-3414105
- LFB speed signal cable > Sony/Phonocar 12 pin: 42c-3414107
- LFB speed signal cable > Alpine I2C 12 pin: 42c-3414115
- LFB speed signal cable > Blaupunkt/China HU/Kenwood 12 pin: 42c-3414124
- LFB speed signal cable > Clarion 12 pin: 42c-3414127
- LFB speed signal cable > JVC 3.5mm jack 12 pin: 42c-3414128
- LFB speed signal cable > Zenec II Lead 12 Pin: 42c-3414129
- LFB speed signal cable > Zenec I Lead 12 Pin: 42c-3414130
- LFB speed signal cable > JVC 1 Lead 12 Pin: 42c-3414140
General installation instructions
Review
- 1: Checking all operating functions and vehicle setting functions of the OEM device
- 2: De-energize the OEM device
- 3: Check all interface connections for correctness and continuity without voltage
Connection and connection sequence
- 1: De-energize the settings and hardware configuration of the interface
- 2: Check the configuration of the radio connection cable
- 3: Connect the radio connection cable according to the operating instructions for the retrofit device
- 4: Connect all other connections according to the operating instructions for the retrofit device
- 5: Connection of the complete installation to the vehicle with live connection last
- 6: Software configuration of the interface according to the instructions in the article text and in the BDA
- 7: Configuration of the retrofit device according to the operating instructions for the retrofit device Steering wheel remote control/camera/FSE/antenna phantom power and others
- 8: Function test steering wheel remote control and vehicle
Changes to the hardware configuration of the interface and the radio connection cable
- 1: Carry out changes without tension
- 2: Connection after change see above 5 to 8
In the event of a malfunction of the interface or the vehicle
- 1: Retrofit to the OEM device
- 2: Operate OEM device
- 3: Establish CAN bus silence
- 4: Checking the hardware configuration of the interface
- 5: Connection after CAN bus rest see above 5 to 8
- Connections, connection changes, alternative connections, connections of loose cables or connection extensions of loose cables specified in the information text or the operating instructions are for guidance and information purposes only for trained specialist personnel.
Additional connections, changes to the cable configuration of the wiring harness or use of alternative connections or connection extensions
- 1: Connections and modifications must only be carried out by trained specialist personnel
- 2: Connections and modifications must be checked for any manufacturer approvals or manufacturer warranty conditions that may be affected by the modifications before connection
- 3: Connections and modifications must be checked for function and correctness before connection by measuring and adjusting using the vehicle's cable assignment diagram
- 4: Connections and modifications are made on your own responsibility without any guarantee of function
- 5: Connections and modifications are carried out under your own responsibility without guarantee of damage to the vehicle, the retrofit device or the interface
- 6: Modifications to the pre-assembled wiring harness may invalidate the product warranty
Download data sheet
