JL Audio XDM1000/5V2

The XDM1000/5V2 is an impressive 5-channel marine amplifier from JL Audio. This high performance amplifier delivers a sensational 100 watts RMS per channel at 2 ohms. With advanced technologies that maximize audio quality and fidelity, the M1000/5V2 is not just an amplifier, but an all-in-one solution to power a powerful marine audio system. Thanks to its sealed and corrosion-resistant design, it is perfectly suited to the demands of the marine environment. Whether you want to drive two high-quality speaker systems or a dual subwoofer system, the XDM1000/5V2 is an unstoppable powerhouse that won't let you down.

• 5-channel class D marine system amplifier, 100 W x 4 @ 2 Ω + 600 W x 1 @ 2 Ω - 14.4 V
• Here is the perfect all-in-one solution to drive a powerful marine audio system with 4 speakers + two subwoofers. The M1000/5v2 delivers up to 1000W of clean power and can comfortably drive two pairs of high quality component speaker systems at 75W x 4 @ 4 Ω, while delivering a solid 600W of power to a dual subwoofer system. The breakthrough that makes so much power possible in such a small enclosure is our NexD Switching Amplifier Design™.
• The M1000/5v2 includes a 12 dB/octave high-pass filter for one main channel pair, a 12 dB/octave high-pass or band-pass filter for the other main channel pair and a variable slope low-pass filter for the subwoofer channel. All three filters offer infinitely variable cut-off frequency selection from 50-500 Hz. The filters of this amplifier can also be configured as a true 3-way crossover, with a low-pass filter for the subwoofer channel, a band-pass filter on channels 3 and 4 and a high-pass filter on channels 1 and 2. A "x10" multiplier switch on the high-pass filter of Ch. 1 & 2 allows the cut-off frequency to be set from 50-500 Hz or 500-5000 Hz.
• With an additional HD-RLC remote control (sold separately), the subwoofer output level or the master volume of the amplifier for all channels can be controlled directly from the control desk. The M1000/5v2 also features the v2 specification function set, which consists of an auto power-on function (via signal detection or DC offset detection) and a differential balanced dual-range input section that can handle a wide range of input voltage levels.
• This amplifier features a white and gray powder coat finish, a sealed cover for the controls and stainless steel hardware for durability in the marine environment.

• Frequency response (main channels) 12 Hz - 22 kHz (+0, -1dB)
• Frequency response (subwoofer channel) 10 Hz - 1 kHz (+0, -1dB)
• Signal-to-noise ratio, relative to the highest rated power (main channels) >104 dB below the rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth)
• Signal-to-noise ratio, relative to 1 W >84 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth)
• Attenuation factor @ 4 Ω >150 / 50 Hz
• Attenuation factor @ 2 Ω >75 / 50 Hz
• THD+N @ Nennleistung (Hauptkanäle) <1% @ 2 Ω pro Kanal.
• THD+N @ Nennleistung (Subwoofer-Kanäle) <1% @ 2 Ω pro Kanal.
• Input voltage range @ RCA inputs switchable from 200 mV - 2 V RMS (Low) to 800 mV - 8 V RMS (High)
• Min. copper power / earthing wire cross-section 25mm²
• Fuse 80 A (AFS, AGU or MaxiFuse™)

• Main channels @ 4 Ω 75 W RMS x 4
• Main channels @ 2 Ω 100 W RMS x 4
• Main channels - bridged @ 4Ω 200 W RMS x 2
• Subwoofer channel @ 4 Ω 400 W RMS x 1
• Subwoofer channel @ 3 Ω 500 W RMS x 1
• Subwoofer channel @ 2 Ω 600 W RMS x 1
• Subwoofer channel @ 1.5 Ω N/A

• Main channels @ 4 Ω 60 W RMS x 4
• Main channels @ 2 Ω 90 W RMS x 4
• Main channels - bridged @ 4Ω 180 W RMS x 2
• Subwoofer channel @ 4 Ω 360 W RMS x 1
• Subwoofer channel @ 3 Ω 480 W RMS x 1
• Subwoofer channel @ 2 Ω 600 W RMS x 1
• Subwoofer channel @ 1.5 Ω N/A

• Filter mode(s): Channels 1 &; 2 (front) High-pass only
• Filter slope(s): Channels 1 & 2 (front) 12 dB/octave
• Filter frequency range: Channels 1 &; 2 (front) 50 Hz - 5 kHz
• Filter mode(s): Channels 3 & 4 (rear) high-pass or band-pass
• Filter slope(s): Channels 3 &; 4 (rear) 12 dB/octave
• Filter frequency range: Channels 3 &; 4 50 Hz - 500 Hz
• Filter mode(s): Subwoofer channel low-pass only
• Filter slope(s): Subwoofer channel 12/24 dB/octave
• Filter frequency range: Subwoofer channel 50 Hz - 500 Hz
• Locked, calibrated filter frequency potentiometers Yes
• Filter defeat function Yes
• Infrasound filter: Subwoofer channel none
• Optional remote control (HD-RLC)
• Remote level modes sub-channel or all channels
• Channel input mode switch Yes (2/4/6 channels)
• Pass-through preamplifier output None
• Selection of the source channel for PreOuts N/A

• Height (H) 52 mm
• Width (B) 374 mm
• Depth (D) 180 mm