If you want to replace your factory radio with an aftermarket radio, you should ensure that the original steering wheel remote control functions are retained.

However, please note that depending on the vehicle equipment, functionality, and software of the retrofit device, certain operating functions may be omitted or replaced by other functions.

Compare the illustrated plugs of the adapter with those in your vehicle and ensure that they fit visually and technically.

Please also check if one of the specified original factory radios was installed in your vehicle.

Before you permanently install the retrofit radio, we recommend that you check the functions of your vehicle, the vehicle settings, and the steering wheel remote control for functionality to ensure that everything works smoothly.

Note

• CAN Bus
• Connection: 40 Pin Quadlock Porsche Connector > Article: 42cx28
• Check dip switch setting for retrofit device
• Vehicles with PCM 3.0 / PCM 3.1 / CRD30 OEM device
• +12V antenna remote chamber A pin 13 check before installation with OEM device:
• Chamber A Pin 14 alternative
• Vehicle settings not supported

Suitable for the following vehicles

• Porsche 911 (977) 08/2008 - 05/2013*
• Porsche Boxster (987) 02/2009 - 01/2012*
• Porsche Boxster (981) 04/2012 - 01/2016
• Porsche Cayenne (9PA/955) 02/2007 - 02/2010*
• Porsche Cayenne (92A/958) 05/2010 - 07/2014
• Porsche Cayenne (92A/958) 10/2014 -12/2017
• Porsche Cayman (987C) 02/2009 - 11/2012*
• Porsche Cayman (987C) 03/2013 - 04/2016
• Porsche Panamera (970) 09/2009 - 04/2013
• Porsche Panamera (970) 07/2013 - 07/2016

The following signals are provided.

• Reimport vehicles or vehicles with differing software may be incompatible in functions.
• +12V ignition terminal 15 1.5A max.
• orange: +12V lighting terminal 58 0.1A max.
• white: +12V reverse signal 1.5A max.
• yellow/green yellow/red: speed signal
• steering wheel remote control
• *Vehicles with MOST OEM sound system > Article: 13-1190-52
• *Vehicles with OEM sound system / speaker cables: +12V amp remote MQS connector chamber C pin 4 white/red check with OEM device

Connection cable for the following radio manufacturers

• Multilead diverse devices: 42arc100
• Alpine 3.5mm jack connection: 42arc101
• Blaupunkt 2010> 3.5mm jack connection: 42arc107
• Blaupunkt 2010> Key1 / Key2 / (GND) connection: 42arc000
• China HU Key1 / Key2 / (GND) connection: 42arc000
• Clarion 3.5mm jack connection: 42arc104
• Digital Dynamics Single Cable Connection: 42arc108
• ESX Key1 / Key2 Connection: 42arc000
• JVC 3.5mm jack connection: 42arc104
• JVC Single Cable Connection: 42arc105
• Kenwood single cable connection: 42arc105
• Kenwood 2017> 3.5mm jack connection: 42arc107
• Kenwood 2020> Key1 / Key2 / GND connection: 42arc000
• Pioneer 3.5mm jack connection: 42arc107
• Snooper Key1 / Key2 Connection: 42arc000
• Sony 3.5mm jack: 42arc107
• XZent single-cable connection: 42arc108
• Zenec Single Cable Connection: 42arc108

General Installation Instructions

• Connection and connection sequence
• 1: Make settings and configuration of the interface without voltage.
• 2: Check the configuration of the radio connection cable
• 3: Connect the radio connection cable according to the operating instructions of the retrofit device.
• 4: Connect all other connections according to the operating instructions of the retrofit device.
• 5: Connection of the overall installation to the vehicle with live connection last.
• 6: Configuration of the retrofit device according to the operating instructions of the retrofit device steering wheel remote control/camera/telephone hands-free system/antenna phantom power supply and more
• Changes to the configuration of the interface and the radio connection cable
• 1: Carry out changes without tension
• 2: Connection after change see above 5 and 6
• The connections, connection changes, alternative connections, connections of loose cables, or connection extensions of loose cables specified in the instructions or the operating manual are intended solely for orientation and information for trained professional personnel.
• "Connections, changes to the cable configuration of the wiring harness, or use of alternative connections or connection extensions"
• 1: Connections and modifications are to be carried out exclusively by trained professionals.
• 2: Connections and modifications must be checked for any manufacturer approvals or any manufacturer warranty conditions that may be affected by the modifications before connection.
• 3: Connections and modifications must be checked for functionality and accuracy before connection by measuring and by matching against the vehicle's wiring diagram.
• 4: Connections and changes are made at your own risk without guarantee of functionality.
• 5: Connections and modifications are made at your own risk without any guarantee against damage to the vehicle, the retrofit device, or the interface.
• 6: Changes to the pre-assembled wiring harness will void the product warranty.