If you want to replace your factory radio with an aftermarket radio, you should ensure that the original steering wheel remote control functions are retained.

However, please note that depending on the vehicle equipment, functionality, and software of the retrofit device, certain operating functions may be omitted or replaced by other functions.

Compare the illustrated plugs of the adapter with those in your vehicle and ensure that they fit visually and technically.

Please also check if one of the specified original factory radios was installed in your vehicle.

Before you permanently install the retrofit radio, we recommend that you check the functions of your vehicle, the vehicle settings, and the steering wheel remote control for their functionality to ensure that everything works smoothly.

Note

• CAN Bus
• Connection: ISO / 10 Pin ISO / Mini ISO Connector Mercedes
• Check dip switch setting for retrofit device
• Vehicles Mercedes with Audio 5 / Audio 10 1-DIN OEM device
• Vehicles Mercedes with Audio 30 APS 1-DIN OEM Navigation
• Vehicles VW Crafter with RCD 2001 1-DIN OEM device
• 'Vehicles Mercedes / VW with radio preparation > Check connection and pin assignment before installation with OEM device:*'
• Vehicles with differing comfort interior CAN bus connection
• brown-red twisted: CAN high
• brown twisted: CAN low
• CAN Bus and CAN Bus Distributor Threshold Strip
• CAN Bus and Climate Control
• CAN Bus in Mini ISO Connector: Pin 1 Can low / Pin 2 Can high
• CAN Bus in 8 Pin ISO Power Connector: Pin 7 CAN High / Pin 6 CAN Low
• CAN Bus in 18 Pin AMP Connector: Pin 8 CAN low / Pin 9 CAN high / not Robert-Bosch CAN
• OEM devices with ISO block connection
• ISO Extension Speaker 10cm > Item: 1322-02
• Vehicles with 10 Pin ISO / ISO speaker connector OEM sound system without D2B OEM sound system:
• Active system adapter various vehicles ISO>ISO > Article: 13-1190-50

Suitable for the following vehicles

• Mercedes A-Class (W169) 10/2004 - 04/2012
• Mercedes A-Class (C169) 11/2004 - 07/2011
• Mercedes B-Class (T245) 06/2005 - 06/2011
• Mercedes C-Class (W203) 03/2000 - 01/2005
• Mercedes CLK-Class (C208) 07/1999 - 03/2003
• Mercedes CLK-Class (C209) 03/2002 - 05/2005
• Mercedes E-Class (W210) 06/1999 - 12/2002
• Mercedes SL-Class (R230) 08/2001 - 02/2006
• Mercedes SLR (C199) 13/2003 - 12/2009
• Mercedes Sprinter (W906) 04/2006 - 08/2013
• Mercedes Sprinter (W906) 08/2013 - 05/2018
  
• Mercedes Vito/Viano (W639) 07/2003 - 08/2010
  
• Mercedes Vito/Viano (W639) 07/2003 - 08/2010
• Mercedes Vito/Viano (W639) 09/2010 - 03/2014
  
• VW
  
  
• VW Crafter I (2EC/2EK/2F) 03/2006 - 07/2011
• VW Crafter I (2EC/2EK/2F) 07/2011 - 11/2016
• VW
• VW Crafter I (2EC/2EK/2F) 03/2006 - 07/2011
• VW Crafter I (2EC/2EK/2F) 07/2011 - 11/2016

The following signals are provided.

• Reimport vehicles or vehicles with differing software may be incompatible in functions.
• +12V ignition terminal 15 1.5A max.
• orange: +12V lighting terminal 58 0.1A max.
• +12V reverse signal white 1.5A max.
• yellow/green yellow/red: speed signal
• steering wheel remote control

Connection cable for the following radio manufacturers

• Reimport vehicles or vehicles with differing software may be incompatible in functions.
• +12V ignition terminal 15 1.5A max.
• orange: +12V lighting terminal 58 0.1A max.
• white: +12V reverse signal 1.5A max.
• yellow/green yellow/red: speed signal
• steering wheel remote control

Connection cable for the following radio manufacturers

• Multilead diverse devices: 42arc100
• Alpine 3.5mm jack connection: 42arc101
• Blaupunkt 2010> 3.5mm jack connection: 42arc107
• Blaupunkt 2010> Key1 / Key2 / (GND) connection: 42arc000
• China HU Key1 / Key2 / (GND) connection: 42arc000
• Clarion 3.5mm jack connection: 42arc104
• Digital Dynamics Single Cable Connection: 42arc108
• ESX Key1 / Key2 Connection: 42arc000
• JVC 3.5mm jack connection: 42arc104
• JVC Single Cable Connection: 42arc105
• Kenwood single cable connection: 42arc105
• Kenwood 2017> 3.5mm jack connection: 42arc107
• Kenwood 2020> Key1 / Key2 / GND connection: 42arc000
• Pioneer 3.5mm jack connection: 42arc107
• Snooper Key1 / Key2 Connection: 42arc000
• Sony 3.5mm jack: 42arc107
• XZent single-cable connection: 42arc108
• Zenec Single Cable Connection: 42arc108

General Installation Instructions

• Connection and connection sequence
• 1: Make settings and configuration of the interface without voltage
• 2: Check configuration of the radio connection cable
• 3: Connect the radio connection cable according to the operating instructions of the retrofit device.
• 4: Connect all other connections according to the operating instructions of the retrofit device.
• 5: Connection of the overall installation to the vehicle with live connection last.
• 6: Configuration of the retrofit device according to the operating instructions of the retrofit device steering wheel remote control/camera/telephone hands-free system/antenna phantom power supply and more
• Changes to the configuration of the interface and the radio connection cable
• 1: Carry out changes without voltage
• 2: Connection after change see above 5 and 6
• The connections, connection changes, alternative connections, connections of loose cables, or connection extensions of loose cables specified in the instructions or the operating manual are intended solely for orientation and information for trained professional personnel.
• "Connections, changes to the cable configuration of the wiring harness, or use of alternative connections or connection extensions"
• 1: Connections and modifications are to be carried out exclusively by trained professionals.
• 2: Connections and modifications must be checked for any manufacturer approvals or any manufacturer warranty conditions that may be affected by the modifications before connection.
• 3: Connections and modifications must be checked for functionality and correctness before connection by measuring and by matching against the vehicle's wiring diagram.
• 4: Connections and changes are made at your own risk without any guarantee of functionality.
• 5: Connections and modifications are made at your own risk without any guarantee against damage to the vehicle, the retrofit device, or the interface.
• 6: Changes to the pre-assembled wiring harness will void the product's warranty.